EFFECT OF GROOVE DEPTH ON WHEAT SIZING REDUCTION AT THE FIRST BREAK ROLLERS
DOI:
https://doi.org/10.17501/Keywords:
wheat milling, groove profiling, size reduction, first break rolls, particle size distributionAbstract
This research looked at how depth of grooves in the first set of break rolls affected sizing process for wheat. These rolls have a modified Dawson-type surface corrugation profile, with groove depths of 0.981 and 1.069 mm. The First break rolls were set up with following operational parameters: fast roll speed of 500 rpm, roll gap of 0.6 mm, and roll differential of 2.5:1. Coarse fraction increased, however sizing, large middlings, fine fraction, and first break flour all reduced as groove depth increased. Since cv. Gerek-79 is structurally more malleable than the other cultivars, it suffered more during the size reduction process. Although it was noticed that starch damage in the first break flour of all cultivars decreased with increasing groove depth, the least amount of starch damage was obtained with cv. Gerek-79 during the size reduction procedure. First break flours from all three varieties did not differ in their Zeleny sedimentation levels based on groove depth. During the first broken rolls' size reduction procedure, the power and energy consumptions of the two groove kinds were nearly identical. Therefore, optimizing groove geometry is crucial for achieving a balance between targeted flour quality, grain structure, and energy consumption. This directly contributes to improving yield and quality control strategies in industrial-scale milling.
References
AACC International. (1999). Approved methods of analysis (11th ed., Method 76-31.01). St. Paul, MN: AACC International. Available online only.
AACC International. (2000). Approved methods of analysis (10th ed., Method 46-10.01). St. Paul, MN: AACC International. Available online only.
Amin, M. N., Hossain, M. A., & Roy, K. C. (2004). Effects of moisture content on some physical properties of lentil seeds. Journal of Food Engineering, 65(1), 83–87.
IBM Corp. (2012). IBM SPSS Statistics for Windows, Version 20.0 [Computer software]. Armonk, NY: IBM Corp.
Arora, S. (2003). The effect of enzymes and starch damage on wheat flour tortilla quality (Master’s thesis). Texas A&M University, College Station, TX, United States.
Barrera, G. N., Pérez, G. T., Ribotta, P. D., & León, A. E. (2007). Influence of damaged starch on cookie and bread-making quality. European Food Research and Technology, 225(1), 1–7.
Campbell, G. M., & Webb, C. (2001). On predicting roller milling performance. Powder Technology, 115(3), 234–242.
Campbell, G. M. (2007). Roller milling of wheat. In Referex Engineering Collection: Chemical, Petrochemical & Process. Elsevier Science. Retrieved from http://www.engineeringvillage.com
Cleve, H., & Will, F. (1996). Research with the help of the varioroll. Cereal Science Today, 11(2), 128– 132.
Creason, H. (1975, January). Grinding and corrugating rolls. Bulletin of the Association of Operative Millers, 3569.
Danciu, C., & Danciu, I. (2010a, October 21–23). Energy saving opportunities related to the size reduction for the first break in wheat milling, with a newly designed micromill. In Selected Topics in Energy, Environment, Sustainable Development and Landscaping (Conference presentation). Romania.
Danciu, I., & Danciu, C. (2010b). Assessment of the energy consumption for the first breaking step depending on the break adjustment in the wheat milling process. In Proceedings of the 2nd International Conference on Manufacturing Engineering, Quality and Production Systems (pp. 235–238). WSEAS Press, Constanța, Romania.
Danciu, C., & Danciu, I. (2011). The grinding resistance of the wheat grain related to the grinding degree for the first break in the wheat milling. Bulletin UASVM Agriculture, 68(2), 235–242.
Delcour, J. A., & Hoseney, R. C. (2013). Principles of cereal science and technology (3rd ed.). St. Paul, MN: AACC International, Inc.
Deshpande, S. D., Bal, S., & Ojha, T. P. (1993). Physical properties of soybean. Journal of Agricultural Engineering Research, 56(1), 89–98.
Dubat, A. (2004). The importance and impact of starch damage and evolution of measuring methods (Technical report No. SDmatic, pp. 1–5). Chopin Technologies.
Elgün, A., & Ertugay, Z. (2002). Tahıl işleme teknolojisi [Cereal processing technology]. Atatürk Üniversitesi Ziraat Fakültesi Yayınları No. 718. Erzurum, Türkiye. (In Turkish)
Fang, Q., Bölöni, I., Haque, E., & Spillman, C. K. (1997). Comparison of energy efficiency between a roller mill and a hammer mill. Applied Engineering in Agriculture, 13(5), 631–635.
Fang, Q., Haque, E., Spillman, C. K., Reddy, P. V., & Steele, J. L. (1998). Energy requirements for size reduction of wheat using a roller mill. Transactions of the ASAE, 41(6), 1713–1720.
Fang, C., & Campbell, G. M. (2002). Effect of roll fluting disposition and roll gap on breakage of wheat kernels during first-break roller milling. Cereal Chemistry, 79(4), 518–522.
Gehle, H. (1965, January). The MIAG “Vario” rollstand – Design and purpose. Bulletin of the Association of Operative Millers, 2861.
Guritno, P., & Haque, E. (1994). Relationship between energy and size reduction of grains using a three- roller mill. Transactions of the ASAE, 37(4), 1243–1248.
Hareland, G. A. (1998). Effects of break-roll speed differential on product yield and semolina granulation in a durum pilot mill system. Cereal Chemistry, 75(6), 836–840.
Hrušková, M., & Faměra, O. (2003). Prediction of wheat and flour Zeleny sedimentation value using NIR technique. Journal of Food Science, 21(3), 91–96.
Hsieh, F. H., Martin, D. G., Black, H. C., & Tipples, K. H. (1980). Some factors affecting the first break grinding of Canadian wheat. Cereal Chemistry, 57(3), 217–223.
International Association for Cereal Science and Technology (ICC). (1994). Determination of the sedimentation value (according to Zeleny) as an approximate measure of baking quality (Method 116/1, Year of approval 1972). Vienna, Austria: ICC.
Kalkan, F., Singh, A., Vanga, S. K. K., Raghavan, V., & Kara, M. (2014). Effects of tempering moisture and roll differential on wheat size reduction process during the first break rollers. Transactions of the ASAE, 57(5), 1425–1429.
Keskin, S., Ozkaya, H., & Turksoy, S. (2012). Effects of damaged starch on physicochemical properties of wheat flour and its bread making potential. Academic Food Journal, 10(2), 14–18.
Lin, P. Y., & Czuchajowska, Z. (1996). Starch damage in soft wheats of the Pacific Northwest. Cereal Chemistry, 73(5), 551–555.
McCorkle, F. D. (1973, January). Development and operation of the modern roller mill. Bulletin of the Association of Operative Millers, 3362.
Mohsenin, N. N. (1986). Physical properties of plant and animal materials (2nd ed.). New York, NY: Gordon and Breach Science Publishers.
Niernberger, F. F., & Farrell, E. P. (1970, January). Effects of roll diameter and speed on first break grinding of wheats. Bulletin of the Association of Operative Millers, 3154.
Özkaya, H., & Özkaya, B. (2005). Öğütme teknolojisi [Milling technology]. Gıda Teknolojisi Yayınları No. 30, 757 p. Ankara, Türkiye. (In Turkish)
Pasikatan, M. C., Milliken, G. A., Steel, J. L., Haque, E., & Spillman, C. K. (2001). Modeling the energy requirements of first-break grinding. Transactions of the ASAE, 44(6), 1737–1744.
Pomeranz, Y. (1988). Composition and functionality of wheat flour components. In Y. Pomeranz (Ed.), Wheat: Chemistry and technology (Vol. II, 3rd ed., pp. 219–370). St. Paul, MN: American Association of Cereal Chemists.
Posner, E. S., & Hibbs, A. N. (2011). Wheat flour milling (2nd ed.). St. Paul, MN: American Association of Cereal Chemists, Inc.
Reddecliffe, T. (2001). Optimising durum wheat yield and quality (Master’s thesis). Lincoln University, Lincoln, New Zealand.
Schumacher, F. (1967, January). Technical aspects of grinding with roller mills. Bulletin of the Association of Operative Millers, 2956.
Suthar, S. H., & Das, S. K. (1996). Some physical properties of karingda (Citrullus lanatus (Thumb) Mansf.) seeds. Journal of Agricultural Engineering Research, 65(1), 15–22.
Ward, A. B., & Shellenberger, J. A. (1951, January). Grinding with controlled roll pressure. Bulletin of the Association of Operative Millers, 1907.
Williams, P. C., Kilborn, R. H., Voisey, P. W., & Kloek, M. (1987). Measuring wheat hardness by revolutions per minute reduction. Cereal Chemistry, 64(5), 422–427.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Proceedings of the International Conference on Agriculture

This work is licensed under a Creative Commons Attribution 4.0 International License.

